2.8L Injection ~ Ford Capri

LORA
Original


Updated:

88

2.8L Injection ~ Ford Capri

1980's Retro Classic Fastback Coupe.

The Ford Capri is a fastback coupé built by Ford of Europe, designed by Philip T. Clark, who was also involved in the design of the Ford Mustang. It used the mechanical components from the Mk2 Ford Cortina and was intended as the European equivalent of the Ford Mustang. The Capri went on to be highly successful for Ford, selling nearly 1.9 million units in its lifetime. A wide variety of engines were used in the car throughout its production lifespan, which included the Essex and Cologne V6 at the top of the range, while the Kent straight-four and Taunus V4 engines were used in lower-specification models. Although the Capri was not officially replaced, the second-generation Probe was effectively its replacement after the later car's introduction to the European market in 1994.For the 1982 model year, the Essex 3.0 V6 powerplant which had been the range topper since September 1969 was dropped, mainly because of ever more strict emissions regulations, that Ford knew the old Essex V6 design could not meet, a new sporty version debuted at the Geneva Motor Show, called the 2.8 Injection. The new model was the first regular model since the RS2600 to use fuel injection. Power rose to a claimed 160 PS (118 kW), even though tests showed the real figure was closer to 150 PS (110 kW), giving a top speed of 210 km/h (130 mph), but the car still had a standard four-speed gearbox. The Capri 2.8 Injection breathed new life into the range and kept the car in production 2–3 years longer than Ford had planned. The four-speed gearbox was replaced with a five-speed unit early on – at the same time Ford swapped the dated looking chequered seats for more luxurious looking velour trim. A more substantial upgrade was introduced in 1984 with the Capri Injection Special. This development used half leather seating and included a limited slip differential. Externally the car could be easily distinguished by seven spoke RS wheels (without the customary "RS" logo since this was not an RS vehicle) and colour-coded grille and headlamp surrounds. At the same time the 2.0 Capri was rationalised to one model, the 2.0 S, which simultaneously adopted a mildly modified suspension from the Capri Injection. The 1.6 model was also reduced to a single model, the 1.6 LS.By the 1986 model year - the Capri's final year on sale - the range had been rationalised even further to just the 1.6 Laser, 2.0 Laser and the 2.8 Injection.

Version Detail

SD 1.5
540
10
✨2.8L Injection ~ Ford Capri✨ 1980's Retro Classic Fastback Coupe The Ford Capri is a fastback coupé built by Ford of Europe, designed by Philip T. Clark, who was also involved in the design of the Ford Mustang. It used the mechanical components from the Mk2 Ford Cortina and was intended as the European equivalent of the Ford Mustang. The Capri went on to be highly successful for Ford, selling nearly 1.9 million units in its lifetime. A wide variety of engines were used in the car throughout its production lifespan, which included the Essex and Cologne V6 at the top of the range, while the Kent straight-four and Taunus V4 engines were used in lower-specification models. Although the Capri was not officially replaced, the second-generation Probe was effectively its replacement after the later car's introduction to the European market in 1994. Parameters: Yet another Mix v.2 LoRA: 1 4:3 ar DPM++3m SDE Karras Steps: 30 CFG: 3 Clip: 2

Project Permissions

Reprinting is strictly prohibited

    Use Permissions

  • Use in TENSOR Online

  • As a online training base model on TENSOR

  • Use without crediting me

  • Share merges of this model

  • Use different permissions on merges

    Commercial Use

  • Sell generated contents

  • Use on generation services

  • Sell this model or merges

Comments

Related Posts

Describe the image you want to generate, then press Enter to send.